Residential · Miami, FL
When a gate starts sagging, dragging, or won’t latch, the hinge welds and latch posts are usually the failure point. Titan Mobile Welding Miami has served Miami since 2016, providing on-site gate welding repair for steel, wrought iron, and aluminum gates so they swing true and lock securely again.
We start with safe, square setup. That means checking hinge alignment, post plumb, and hinge barrel wear, then bracing the gate to remove load before we cut, grind, or gouge out cracked welds. We prep to clean, bright metal using flap discs and wire wheels, verify base metal type (mild steel, galvanized steel, stainless, or aluminum), and choose the right process, typically GMAW (MIG) for speed and control, or GTAW (TIG) for thin or cosmetic work.
Miami-area gates live in corrosion and heat, so repairs have to address more than the crack. For coastal air and wet seasons, we remove rust scale, seal pinholes, and rebuild lost material at hinge plates and latch receivers, then dress the welds for smooth swing clearance. Where galvanized components are involved, we manage zinc contamination by cleaning properly and using compatible primers and cold-galvanizing touch-up where appropriate; for aluminum gates, we use aluminum filler wire/rod and control heat to prevent warping. Finish options include rust-inhibitive primer, topcoat-ready surfaces, and anti-seize on hinge pins to reduce future binding.
Customers choose us because we solve the root cause, not just re-tack a broken spot. We bring a fully equipped mobile rig with generator power, welding machines, grinders, clamps, levels, and jacks so most gate welding repair is completed in one visit without removing the gate. You get clear, written estimates, straight answers about whether the issue is weld fatigue, hinge misalignment, post movement, or latch geometry, and work performed by a licensed and insured contractor.
Before we wrap up, we do a full function test: smooth swing, consistent reveal, proper stop contact, and positive latch engagement without lifting the gate by hand. We confirm hinge pin orientation, verify striker alignment, and check for interference at the bottom rail so it does not scrape concrete or pavers. You receive a walkthrough of what failed, what was reinforced (hinge plates, gussets, latch tabs, or post collars), and care steps like lubrication intervals and paint touch-up to slow corrosion.
Yes. We provide a free written estimate that outlines the repair or fabrication scope, materials, and expected timeline.
Yes. We perform TIG welding for aluminum and stainless when the job calls for controlled heat and clean appearance, and we also handle steel with MIG or stick depending on conditions.
Yes for many light structural repairs and reinforcements such as brackets, posts, frames, and supports. If engineering or permitting is required for your project, we will flag that up front.
We can grind and clean the weld area and remove sharp edges so it is ready for primer and paint. Final coating selection and color matching can be handled by the customer or coordinated as part of the scope.
Photos from a few angles, approximate dimensions, metal type (if known), thickness or tube size, and what the part is used for. Include whether it is on-site only or can be removed and brought to a shop.
Gate welding repair is usually needed when hinge welds crack, latch tabs tear, or a gate sags enough that the lock will not catch. Those problems often show up as dragging on the driveway, grinding noises at the hinge barrel, or a latch that only works if you lift the gate. Titan Mobile Welding Miami provides on-site hinge and latch welding repair for residential and commercial swing gates, pedestrian gates, and welded steel frames, with a focus on alignment, reinforcement, and corrosion control, not quick patches.
A proper repair starts with diagnosis. We check hinge spacing, hinge barrel condition, and whether the gate frame is racked or the post has shifted. Then we unload the hinge area with bracing, remove failed weld metal, and prep the joint for full penetration where the design allows. Depending on thickness and access, we add reinforcement such as gussets, hinge backing plates, or a wrap collar at the post to spread the load and reduce repeat cracking.
Material matters. Wrought iron and mild steel typically weld clean with MIG, while thin decorative sections may call for TIG to control heat and keep lines crisp. Aluminum gates require dedicated aluminum filler and careful heat management to avoid distortion. If the gate includes galvanized parts, we handle surface prep and post-repair protection so the repair does not become a rust hotspot.
After welding, we verify swing, gap, and latch engagement under real use. You get a clear explanation of what was repaired, what was reinforced, and what maintenance will help, like lubricating hinge pins and keeping paint intact at welded areas. If you need gate welding repair in Miami, call Titan Mobile Welding Miami for a free written estimate.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Miami. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
