Residential · Miami, FL
When a metal fence starts leaning, cracking at welds, or dragging at the gate, the fix has to be structural, not cosmetic. Titan Mobile Welding Miami has served Miami since 2016, providing on-site metal fence repair with professional welding and steel fabrication to restore strength, alignment, and security.
Every metal fence repair starts with a quick structural assessment so the fix lasts. We check post plumb, rail straightness, panel spacing, hinge and latch wear, and the condition of existing welds, fasteners, and anchors. Typical prep includes removing loose rust scale, paint, and contaminated metal at the joint, then beveling or opening cracks for full weld penetration. When needed, we cut out failed sections and splice in new steel tube, angle, flat bar, or picket material, then square and clamp everything before welding so the fence lines up again.
South Florida heat, rain, and salt air accelerate corrosion, especially at ground contact, base plates, and water-trap joints. After welding, we manage spatter, grind where required for fit and appearance, and address rust-prone areas with primer and coatings matched to your fence type. We repair and reinforce gates with hinge barrel replacement, hinge relocation, latch realignment, and anti-sag bracing, so gates swing freely without scraping concrete. If your fence is galvanized, we discuss proper touch-up options for cut and weld areas and focus on sealing exposed steel to slow future rust.
Miami customers choose us because we show up equipped to fix fences in one visit, not take measurements and disappear. Our mobile setup supports common fence materials and thicknesses, and we bring the clamps, levels, grinders, and cutting tools needed to straighten, brace, and weld safely on site. You get clear options, repair versus replace, reinforce versus patch, and we explain what caused the failure, impact damage, settling, or corrosion at a post or rail. Work is done by licensed and insured welders with a free written estimate, and we aim for clean welds, solid fit-up, and reliable gate operation.
Before we wrap up, we do a walkthrough with you to confirm alignment, gate swing, latch engagement, and that repaired sections match the fence line and height. We tidy the work area, verify there are no sharp edges, and point out any adjacent sections that may be nearing failure so you can plan ahead. You receive a written scope of work, the materials used (for example, new steel tube, angle braces, hinges, or base plates), and care guidance for paint and rust prevention. If you need add-ons like new gate stops, drop rods, or extra bracing, we can usually fabricate and install them during the same appointment.
Yes. We provide a free written estimate that outlines the repair or fabrication scope, materials, and expected timeline.
Yes. We perform TIG welding for aluminum and stainless when the job calls for controlled heat and clean appearance, and we also handle steel with MIG or stick depending on conditions.
Yes for many light structural repairs and reinforcements such as brackets, posts, frames, and supports. If engineering or permitting is required for your project, we will flag that up front.
We can grind and clean the weld area and remove sharp edges so it is ready for primer and paint. Final coating selection and color matching can be handled by the customer or coordinated as part of the scope.
Photos from a few angles, approximate dimensions, metal type (if known), thickness or tube size, and what the part is used for. Include whether it is on-site only or can be removed and brought to a shop.
Metal fence repair is not just about making a break look better, it is about restoring the load path so panels stay straight, posts stay plumb, and gates work without binding. Titan Mobile Welding Miami provides on-site welding and fabrication for steel and iron fences, from cracked welds and rusted rails to bent pickets and sagging gates. Because we are mobile, most repairs are handled at your property with the right tools to cut, fit, clamp, and weld safely, then seal and protect the repaired area to slow corrosion.
Common calls for metal fence repair include posts loosening at the base, rails separating at old welds, and gates dragging because the hinge side has shifted. We correct the underlying issue first, re-square the opening, re-plumb posts when possible, and add reinforcement where stress concentrates (hinge zones, corners, and long spans). Depending on the fence design, repairs may involve welding new steel tube or flat bar, adding a gusset plate, replacing a hinge barrel, or installing an anti-sag brace so the gate carries weight correctly.
Corrosion is another major driver, especially at ground contact and anywhere water sits inside hollow sections. If the metal is too thin to hold a safe weld, we recommend cutting back to sound steel and splicing in new material rather than chasing pinholes. After welding, we grind only where needed for fit and appearance, then prep for primer and paint or other coating touch-ups to reduce flash rust and extend service life.
If you want a repair that looks clean and holds up, schedule an on-site assessment. We will measure, explain options, and provide a free written estimate for a practical fix that restores security and gate function while keeping the fence line straight.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Miami. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
